Krk ERGO Manuale Utente

10It’s time to get ready to set up your mixing environment. Thisconsists of 3 easy steps: 1) Set up your monitors - you may have already put them exac

TTwwoo--CChhaannnneell SSeett UUpp • Near-Field Configuration– In a control room situation, themonitors are often times placed on the meter bridge

12AAddddiinngg aa SSuubbwwooooffeerr Begin by determining the best location for your subwoofer. Ifpossible, the optimum set up would reflect that s

13SSeettttiinngg UUpp aa 22..11 SSyysstteemm wwiitthh TTwwoo FFuullll RRaannggee MMoonniittoorrss (Figure 3.4)CCoonnffiigguurraatti

14UUssiinngg AAnnaalloogg ((LL && RR)) aanndd DDiiggiittaall ((SSPPDDIIFF)) IInnppuuttss Here are a few tips to keep in mind when dea

15RoomPerfect™ can derive information about: • Room acoustic properties and modes (peaks and dips in the room) • Power response throughout the room •

16This section describes ERGO’s Control Panel including configurable parameters and system information. (Figure 4)NNootteeRemember that ERGO Con

17ERGO Cal is your friend. Get to know, and love it. Double click ERGO Cal icon (located as shortcut in your desktop or within the Applicatio

1855..22 CCaalliibbrraattiioonnSSppeeaakkeerr MMooddee This window will inform you of which, if any, buttons are selectedon ERGO—A, B/Sub, both, o

1955..22..11 EEnnaabblliinngg CCaalliibbrraattiioonn If the Calibrate button is Off, check ERGO’s Back panel andpress it (Figure 5.8). The Calibrate

21.IInnttrroodduuccttiioonn ...

20In the second adjustment, the volume is system dependent.55..22..33 FFooccuuss PPoossiittiioonn MMeeaassuurreemmeenntt The following window prepa

21One Mississippi, two Mississippi... (Figure 5.14)Well, how did things go? If the level did not fall within an acceptable parameter, ER

22If the Focus measurement was Ok, ERGO will instruct you toplace your measurement mic in Room Position 1, then click EEnntteerr.(Figure 5.18)If there

2355..22..55 RRoooomm CCoorrrreeccttiioonn The room correction score is a measure of how much processingis being performed in the room correct

24Then, click YYEESSto store your measurements (Figure 5.23). If you choose to continue with more measurements, select YESand follow ERGO’s prompts

25This will take you to ERGO Cal’s initial screen...and you’re done.(Figure 5.26)55.. EERRGGOO CCaalliibbrraattiioonn SSooffttwwaarree ((EERRGGOO

26The following are tips that you probably already know, but itwould be a good idea to read them as a refresher. You know theold adage...better safe t

27• What if you don’t have SPDIF Out? No problema, amigo. Just plug the outputs that are currently connected to your monitors into ERGO’s

28CCoonnffiigguurriinngg EERRGGOO IInnppuuttss aanndd OOuuttppuuttss iinn YYoouurr DDAAWW SSyysstteemm ERGO inputs and outputs will appear as

29Below you will find information regarding integration of ERGOinto various DAWs. 88..11 PPrroo TToooollss®® If your Pro Tools hardware provides a S

3Thank you for purchasing the ERGO Room Correction System.We appreciate your trust in us. ERGO (EEnhanced RRoom GGeometry OOptimization) is an

3088..33 AAbblleettoonn LLiivvee™™If this is a new installation and ERGO is your only FireWire interface, set Ableton for ASIO mode by going into the

31If you’re having trouble with ERGO, check out these tips. PPoowweerr LLEEDD//kknnoobb LLEEDDss ddoo nnoott iilllluummiinnaattee wwhheenn ppoo

32TThhee CCaalliibbrraattiioonn MMiicc lleevveell iiss nnoott lloouudd eennoouugghh.. • Turn up the volume on your speakers. The speakers need

33WWhhiillee uussiinngg EERRGGOO iinn WWDDMM MMooddee,, II’’mm nnoott aabbllee ttoo sseelleecctt aabbuuffffeerr ssiizzee vvaalluuee ffrr

34PPrroocceessssiinngg- Processing 400 MHz Blackfin DSP - RoomPerfect™ Algorithm Sample Rate 96 kHz - Room Correction Frequencies 20-500 HzAAuuddiioo

35AA//DD - short for Analog to Digital Conversion. The conversion ofanalog data or information into digital or binary form (See binary).AASSIIOO–

36SSaammpplliinngg FFrreeqquueennccyy- The number of digital snapshots or samples taken of an analog audio signal in one second neces

Copyright © 2008 by KRK Systems, LLCERGO is a trademark of the Stanton Group. RoomPerfect is a trademark of Lyngdorf AudioAll other trademarks are pro

411..33 HHooww ddooeess EERRGGOO wwoorrkk??ERGO takes a stereo audio stream from the analog or digital(SPDIF or FireWire) domain and processes it t

511..55 SSyysstteemm RReeqquuiirreemmeennttssA computer is required for performing room measurement andanalysis. Minimum required computer specificat

6“The ideal response is flat and without reflections” is a statementyou’ll hear if you ask people what the perfect sound would befor them. However, fo

722.. EERRGGOO PPaanneellss aanndd CCoonnnneeccttiioonnss22..11 BBaacckk PPaanneell aanndd CCoonnnneeccttiioonnss In the Back panel (Figure 2)

8• You have a complex or well-established FireWire configuration on your computer and don’t want to interfere with it. • You are using an

9FFooccuuss//GGlloobbaall ERGO has two modes of operation; Focus and Global. In Focus mode all of ERGO's processing power is correcting thefocus